Weiler 56490 Mandrino di montaggio per dischi da taglio con foro per perno da 3/8", solo mandrino con stelo da 1/4"

Brand:Weiler

3.7/5

€
37.73

Il mandrino Weiler 56490 monta in modo sicuro un disco da taglio di tipo 1 con un foro da 3/8 su una smerigliatrice che accetta steli da 1/4. Il mandrino è progettato per adattarsi a dischi da taglio da 0,035 a 1/4 di spessore ed è realizzato in acciaio al carbonio per una maggiore resistenza e una maggiore durata dell'utensile. Il mandrino è costituito da un gambo e una vite. Il gambo si inserisce in un mandrino per smerigliatrice. L'estremità del perno del gambo accetta un disco da taglio e la parte a vite del mandrino si infila nel gambo, fissando il disco al mandrino.SpecificheDimensione del perno3/8Spessore del disco accettatoda 0,035 a 1/4Diametro del gambo1/4Merit Abrasives produce abrasivi per le industrie di sbavatura e finitura. Merit, fondata nel 1945 e con sede a Cleveland, OH, soddisfa gli standard 9000 e 14001 dell'Organizzazione internazionale per la standardizzazione (ISO).

Quantity

Aggiungi al carrello Compra subito

EAN: 0012382564902

Categories: Prodotti industriali e scientifici, Prodotti abrasivi e di finitura, Accessori abrasivi, Mandrini,

Fare clic sul collegamento Weiler nella parte superiore di questa pagina per saperne di più sulla nostra azienda familiare di quarta generazione con sede a Cresco, PA. Tacca a testa piatta per una vestibilità aderente; Lo stelo da 1/4 si adatta alla maggior parte delle smerigliatrici e degli utensili pneumatici. Il foro dell'albero da 3/8 si adatta ai dischi da taglio e da strappo di tipo 1. Leggero, resistente e l'accessorio perfetto per la smerigliatrice.

Brand	Weiler
Compatible Devices	Die Grinder
Construction Type	Cut-off Wheels
Country of Origin	USA
Domestic Shipping	Item can be shipped within U.S.
Grit Material	Carbon Steel
International Shipping	This item can be shipped to select countries outside of the U.S.
Is Discontinued By Manufacturer	No
Item model number	56490
Manufacturer	Weiler Corporation

5 Star

4 Star

3 Star

2 Star

1 Star

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con^*

La tua valutazione

Scritto da: Larry C.

Mandel 1/4 drive

Worked just fine, held the disk without any slipping, used it on several different tools, air drive and electric.

Scritto da: shawn

Works great in my MAC tool

This works great in my right angle air MAC Tool

Scritto da: Alvin Lenzen

Fast delivery

Wrks great fit perfectly

Scritto da: Duhuh

Works

Quick change out of grinder disks

Scritto da: Shooter McGavin

Four stars: not ground concentric.

I have two of these in two different grinders. They were both (and/or my grinders' collets) a bit out of whack.. One of my grinders normally runs rather smoothly. But with this mandrel chucked in it, it vibrated so bad that the cutoff discs frayed, the switch fell apart, the power leads broke off, and the case "ultrasonically" welded itself together in two spots. I had to tap it with a hammer to get the halves apart. After repairing the grinder, I chucked this mandrel back in and "turned" it true with a thick cutoff disc in another grinder while this mandrel was spinning at 25K rpm. You can easily see where the high/low spots are, due to the black finish. When there's no more black, it should be better. After making it concentric and removing a bit of unnecessary mass from the head, the vibrations went away. I also noticed the discs did not sit flat, so I took the screw out and faced the part that the bottom of the disc sits on, too, using the same method. Unfortunately, I had no way to face the bottom of the disc retaining screw in situ, but it was close enough to begin with that the discs now sit perfectly flat, and I did not need to fudge with it by, say, adding a cardboard washer or an O-ring between the disc and the retaining screw. The grinder is now super smooth and working fantastic with this mandrel. I think I'm gonna dedicate this grinder to cutoff discs, changing them out only with the mandrel screw. I'm afraid I might lose some smoothness/concentricity if I re-chuck the mandrel. These mandrels are made of carbon steel and the screw and threading are fine. They are solid. They are cheap enough that I would recommend them. Just have another grinder or Dremel tool handy, I think after going through this, I would true up any large mandrel in situ on any tool rotating at ridiculous RPMs, unless it were chrome plated and extremely well balanced to begin with. It's very fast and easy. Just keep both grinders oriented the same direction when you grind: tip to tip, butt to butt. If you try to "69" it, the cutting disc will just loosen, itself. This makes me wonder how reversible air grinders keep the cutting disc in place.

Scritto da: Opie

Works great with my die grinder

Works great with my die grinder

Scritto da: Jb

Perfect fit

Used this with circular saw blade (reviewed elsewhere) and cordless drill to trim concrete pavers. Sized as advertised.

Scritto da: Phils2888

Nice Cut Off Wheels

Work well in the shop

Scritto da: Daniel Parkes

Great for a die grinder

Using this in my die grinder. Unfortunately it didn’t fit my metric collet so I had to rub the shank down. Shipping took awhile to the uk. Didn’t realise it was in the US! Cuts great and does the job.

Scritto da: Brian

Top value for design & money

This is the very best design ! As the the top removable retaining stud goes through the blade into the stem ! While other versions only use a Phillips head short set screw ironic these are made by a blade company. These much superior by far !!

Scritto da: mb stelmach

The right centre hole size discs.

I've used them professionally for 40yrs+. A must in the aircraft industry.

Scritto da: tree

works

solid

Scritto da: Amazon Customer

Five Stars

Good product.Many thanks.