Freud 03-120: 1/8" (dia.) Punta diritta a scanalatura singola con codolo da 1/4", altezza in metallo duro 5/8" Taglia unica Rivestimento Perma-shield Rosso

Brand:Freud

3.2/5

38.02

DESCRIZIONE DEL PRODOTTO Punta diritta a singolo flauto da 1/8 (diametro) DAL PRODUTTORE Questa punta Freud a singolo flauto è stata progettata per lavori di produzione elevata con una quantità massima di rimozione del truciolo per velocità di avanzamento elevate. Estremità dello scarico della punta per il taglio a tuffo. Coperto dalla garanzia a vita limitata di Freud.

EAN: 7147905907737

Categories:

Ghiaccio nero. + Freud TiCo Hi-Density Carbide = durata e prestazioni 2 volte superiori rispetto alle punte non rivestite standard. Ghiaccio nero. rivestimento per un tagliente freddo e un'evacuazione del truciolo superiore. Specifiche: numero di frese 1, diametro complessivo. 1/8, lunghezza totale 2, gambo diam. 1/4, altezza carburo 5/8.
Batteries Included? ‎No
Batteries Required? ‎No
Brand Freud
Color ‎Perma-shield Coating Red
Country of Origin ‎Italy
Customer Reviews 4.2 4.2 out of 5 stars 148 ratings 4.2 out of 5 stars
Domestic Shipping Item can be shipped within U.S.
Finish ‎Uncoated
Included Components ‎Single Flute Router Bit
International Shipping This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer ‎No
Item model number ‎03-120
Item Package Quantity ‎1
Item Weight 0.12 Pounds
Item Weight ‎1.92 ounces
Manufacturer ‎Freud
Material Blend
Material ‎Blend
Number of Flutes 1
Part Number ‎03-120
Product Dimensions ‎1 x 1 x 1 inches
Size One Size
Size ‎One Size
Style ‎1/8-Inch Diameter by 5/8-Inch Single Flute Straight Router Bit with 1/4-Inch Shank
Warranty Description ‎Freud Limited Tooling Warranty. Contact Freud customer service for more details. 800-334-4107

3.2

10 Review
5 Star
62
4 Star
19
3 Star
5
2 Star
2
1 Star
11

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con*

Scritto da: Jay Batson
Don't go full-depth too-fast
I *might* attribute this to operator error, but I was running a 5/8" deep cut for 3". 5/8" is about as deep as you can get with this bit. After 2", the bit snapped off right at the top of the thin section. (ALWAYS WEAR SAFETY GOGGLES!) When I pulled the cutting portion out, it was pretty damn hot. So, don't rush a deep cut. Take it slow. And wear safety goggles!
Scritto da: straighttalk
Shattered first time it was used.
Shattered first time it was used. Called thinking they would honor the warranty. Told I had to find the broken piece which I could not.
Scritto da: Jeff Garland
Works fine machining balse, light ply and some plastics
I run this on my homemade CNC rotary cutter and it works fine on Balsa, light ply, HDPE and mdf. I typically run it around 5K-10K RPM and 45 inches per minute but your mileage may vary. If you run it too high you will likely burn your material. I actually started a little fire in some MDF running it over 20K RPM and 10 inches per minute. If it stops cutting cleanly then it's dull. Get another cause the cuts just get worse and worse. Works great when sharp.
Scritto da: Beeman
Perfect for our Ikea Hack
Routed a 1/8 dado for 2 24x30x90 back panels to complete carcasses vs purchasing them from Ikea.
Scritto da: david
sharp
great for pattern woodworking
Scritto da: H. Stewart
Cuts well, not great for free hand use.
It's exactly as it is listed so I'll give it high marks. But it's not so easy to use free hand. I'm using it to trim out the corners on picture frames after rabbiting out the back. It's so small I had a hard time seeing what was shadow on the bit and the cut line. I'll go back to the 1/4" going forward. It's probably fine to use on a table but go slow. It's small and single flute.
Scritto da: Woodio
Good 1/8" x 5/8" cutter.
The only thing that I would like better would be a bit that was slightly longer so that it would cut a maximum of 3/4" material. But, knowing that this is exactly as advertised, it is a great cutter and has held up to the task.
Scritto da: Sarah Lance
Pricey but work
Work well in cnc
Scritto da: DAVID C.
Broke right away cutting acrylic
Broke on first use
Scritto da: Marek Z.
Looks different as picture of the product I purchased

Prodotti correlati

Scopri il nostro network internazionale

Spediamo in 28 paesi, oltre 200.000 prodotti. Resta aggiornato, iscriviti alla newsletter.

Shopping Cart