Fastener difficile da trovare 014973323134 323134 TEE DADO, 10-32 X 5/16 "

Brand:Hard-to-Find Fastener

3.1/5

€
38.32

Disponiamo di un'ampia varietà di elementi di fissaggio ideali per molte applicazioni in casa, in azienda, in azienda, nel settore automobilistico e nell'industria. La maggior parte dei nostri elementi di fissaggio ha una leggera zincatura sull'acciaio che conferisce una finitura più resistente alla ruggine. Vendiamo anche prodotti rivestiti e inossidabili per una maggiore resistenza alla ruggine. Disponiamo di molti gradi di elementi di fissaggio che vanno dall'acciaio a basso tenore di carbonio fino all'acciaio temprato e trattato termicamente. Non tutti i dispositivi di fissaggio sono applicabili a tutte le applicazioni, quindi assicurati di testare accuratamente e ottenere il parere di un edificio autorizzato o di un ingegnere edile o strutturale certificato prima di fare affidamento su questi dispositivi di fissaggio per qualsiasi situazione in cui il guasto provocherebbe danni a proprietà o persone.

Quantity

Aggiungi al carrello Compra subito

EAN: 0014973323134

Categories: Prodotti industriali e scientifici, Chiodi, viti e elementi di fissaggio, Noci a T,

Dimensione trapano: 5/16 pollici. Finitura: zinco. Materiale: acciaio. Lunghezza: 5/16 pollici. Diametro: #10.

Batteries Included?	‎No
Batteries Required?	‎No
Brand	‎Hard-to-Find Fastener
Country of Origin	‎China
Customer Reviews	4.1 4.1 out of 5 stars 115 ratings 4.1 out of 5 stars
Domestic Shipping	Item can be shipped within U.S.
Drive System	‎External Hex
Exterior Finish	Zinc
Exterior Finish	‎Zinc
Fastener Type	Weld
Fastener Type	‎Weld
Finish	‎Zinc
Finish Type	‎Zinc
Included Components	‎Tee Nut
Inside Thread Size	‎10-32
International Shipping	This item can be shipped to select countries outside of the U.S. Learn More
Item Dimensions LxWxH	‎2.5 x 1.44 x 1.25 inches
Item model number	‎014973323134
Item Package Quantity	‎1
Item Weight	‎1.51 ounces
Manufacturer	‎Hard-to-Find Fastener
Material	Steel
Material	‎Steel
Measurement System	‎Inch
Metal Type	Alloy Steel, Carbon Steel
Metal Type	‎Alloy Steel, Carbon Steel
Part Number	‎TNS-068-16
Product Dimensions	‎2.5 x 1.44 x 1.25 inches
Shape	‎Round
Size	‎10-32 x 5/16"
Thread Size	#10-32
Thread Size	‎#10-32
Thread Type	‎Fine

5 Star

4 Star

3 Star

2 Star

1 Star

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con^*

La tua valutazione

Scritto da: Darryl

Smaller than I needed

I saw a listing size as larger so for that I'm disappointed but it does look good enough for other tasks

Scritto da: Just Me

It's a peanut what is there to say.

Looks nice has smooth edges should do just what I want nothing more nothing less.

Scritto da: Active Al

The Three Mounting Holes are a Bit Small

ADDED: Originally I had knocked off a start because the three mounting holes were too small. I had to drill out the holes to use even tiny screws. However, I noted that these are advertised as Brad Hold Tee Nuts which means that they are made to be secured with small nails. My fault for not reading the description correctly MODIFIED: I purchased the 5/16 - 18 x 5/8 tee nuts from Hard-To-Find-Fasters on 10 Jul 17 and there were 10 tee nuts in the package. The nuts are 5/8" deep which means this is the length of hole you have to drill. The nuts are sturdy, well finished, and deeper than most. But the three mounting hole are only about 5/64" in diameter. I had to drill them out to 7/64" to put in screws with any meaningful holding power. product. ORIGINAL: If you are securing tee nuts to the back of a mounting surface, then you can probably get by with using small nails for mounting if you want, or even cheaper pronged tee nuts. When this method is used, the bolt goes into the back-end of the tee nut and pulls broad end into the back of the mounting surface - making the tee nut forever tight and secure. The product description advised using a 25/64" drill for installing the tee nut. However, I found out that a 3/8" bit (which is actually slightly smaller) works perfectly. This may be good news for some since 25/64" bits are generally included in large drill bit sets only.

Scritto da: Shemetta Griffin

Good for the price

Love the quality and quantity for the price.

Scritto da: EVA T

Hard-to-Find Fastener

was looking for one with a fit a longer screw and platform to fit for the table leg so had to make some adjustment ,, leg is heavy just hope it will hold

Scritto da: Dr. O

If this is what you need, it will work nicely

Perfect for my application: 1/4-20 threads for a device that has to mount to a photo tripod. The flat sides make it easy to mount in a way that prevents the piece from turning. It is sufficiently well-made -- neither a masterpiece of craftsmanship nor cheap junk. If you need this part, you already know it and are glad to have finally found it. If you don't know why you would need this, you don't need it.

Scritto da: Tim_Fran

Perfect Solution

This item worked great for my application. I wanted to mount a Dog Silencer on a camera tripod but the manufacturer said there was no way to do it. I found that by using this fastener I could mount this tee-nut inside the Dog Silencer case and then use the standard 1/4-20 mounting provided by a camera tripod to hold the unit in place. Works great!

Scritto da: RickieDean

Not heavy duty

This T Nut fastener is fairly lite duty,so if you are thinking of using these to support or anchor something heavy find something more heavy duty these are pretty light weight