0
0

Totale:€ 0.00

Vedi carrelloCheckout
LoginRegister
0

Totale:€ 0.00

Vedi carrelloCheckout
LoginRegister

EZ LOK 400-4-CR Inserti filettati per legno, kit di installazione, acciaio inossidabile, include inserti filettati per coltello 1/4-20 (6), trapano, strumento di installazione

Brand:E-Z LOK

3.5/5

€
69.54

Progettato per l'uso in mobili, mobili, finestre antivento e applicazioni marine. Fornisce una robusta filettatura a macchina nel legno. Ottone, filettature UNC. Installa rapidamente con gli strumenti inclusi. Kit di installazione con inserti, trapano e avvitatore.

Quantity
Aggiungi al carrelloCompra subito

EAN: 0847554007457

Categories: Prodotti industriali e scientifici, Chiodi, viti e elementi di fissaggio, Inserti filettati, Inserti filettati elicoidali,

Progettato per l'uso in mobili, mobili, finestre antivento e applicazioni marine. Fornisce una robusta filettatura a macchina nel legno. Ottone, filettature UNC. Installa rapidamente con gli strumenti inclusi. Kit di installazione con inserti, trapano e avvitatore.
Exterior Finish Brass
Fastener Type Insert
Item model number 400-4-CR
Manufacturer EZ-Lok
Material Stainless Steel
Metal Type Stainless Steel, Brass
Product Dimensions 8 x 2.9 x 1.1 inches; 0.01 Ounces
Thread Size 1/4"-20

3.5

10 Review
5 Star
71
4 Star
14
3 Star
6
2 Star
3
1 Star
7

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con*

Scritto da: James S.
Perfect For Stripped Out Guitar Neck Mount
I bought a used Tele and someone had installed an oversized Sheetmetal screw in the neck mount. Stupid-head! Anyway after installing these my guitar looks and functions perfectly.
Scritto da: Mountain Hiker
Good but not perfect - not as durable as one would wish. Work around exists for inserting
I was using these for river table legs, to insert into VERY hard hickory wood. The 25/64 bit was VERY snug. Had to open it up to 13/32nds in some spots. What I found worked best was a stainless steel 1/2" inch bolt to put them into the wood. Save the special proprietary tool for when you mess up and need to pull one out. The brass inserts are very prone to chipping with too much torque on the EZ Lok insertion tool, but the 1/2" 1/4" 20 bolt worked well to insert. I would buy again now that I know how to use.
Scritto da: Steve Biedrzycki
They don't like hardwood.
Used in black walnut. The notches for the installation bit stripped on several of the inserts I was trying to install. Had to run an 8-32 screw with a nut run down against the insert so I could spin the nut to get my torque to thread it in. Also my installation bit looks like the nubs are rounding out after 20 inserts into black walnut. I love the concept, just wish they were more durable.
Scritto da: Michael McGarghan
Verify your application and measurements
I needed to replace ths failed zinc threaded inserts in hardwood chair. Brass is not recommended but these stainless steel ones are very good. Unfortunately, even with insert tool if they start to misalign when you thread them in, most screw drivers do not fit the slots to un-thread insert. Luckily I was able to use another tool to remove and start again. One insert was slightly tilted, but to my surprise still held tight and finished the job. If you use these to repair a hole like I did, do not use dowels to repair holes first! End grain of dowel is not strong. Use plug cutter to get with grain plug for stronger connection. Titebond glue was strong enough, epoxy was not needed.
Scritto da: A Customer
Worked great
Worked great to fix stripped out hinge screws in wood on my boat. I had no trouble with the included installation tool. I drilled the pilot holes using the included bit and made sure the hole was at least as deep as the insert is long, and the inserts went in very easily. I’d guess that people who broke the installation tool didn’t drill their pilot holes deep enough. I just wish they weren’t so expensive, and that you could buy more inserts separately and save money.
Scritto da: Evan-13
0 stars for the kit, 5 stars for the threaded inserts
The kit is not worth the money. The installation tool broke the first time I used it and almost got permanently lodged into the threaded insert. Additionally the 25/64 drill bit is not big enough for hard wood (bamboo in my case). I assume 25/64 would be fine for softer woods. Instead just go buy a stainless steel machine screw ($2 for 4 — avoid using nickel or brass) and use that to insert the threaded inserts into the wood. For hardwood use a 27/64 drill bit. The stainless steel threaded inserts are VERY GOOD, so just go buy the 10 pack for half the price.
Scritto da: Adam Gardener
Well designed
This is a slick system. The drill bit seems too large for the inserts if you look at them overlapping, but it is just the right size, especially in hard wood, like Oak. If you use it in a soft wood, be sure to drill the pilot hole deep enough, or you will likely strip the wood threads created on entry trying to tighten it after it contacts the bottom of the hole. Also, I used a T-bar style hand driver to drive the inserts into the hole. The custom driver bit they provide is notched to fit small slots on one side of the insert, and this fit easily into my chucked hand driver. It works really well. Hand driving them gives you the control needed to get them started perpendicularly into the hole and then on until tight just below the surface of the piece. Very satisfying result. Of course, you may need to drill an additional distance into the piece with a 1/4 inch bit PRIOR to driving in the inserts in order to accommodate the length of the 1/4 inch bolt you will be using.
Scritto da: Jason
Worked Flawlessly w/ Hardwood Desk Top
I purchased this item to proactively mitigate any problems I might face attaching height-adjustable legs to an incredibly heavy solid wood desk top. I read reports of individuals having challenges using these kits with hardwood but my experience was great. The drill bit worked just as expected and the threaded inserts installed without any problems. I had both sides drilled and inserts installed in less than 10 mins. I would purchase this kit again.
Scritto da: Jan L
Good
Used on a wooden deck to secure a canopy. Easy to use but you must be careful to get the insert straight.
Scritto da: vrb
Good Product!
The insert driver works very well. VRB

Prodotti correlati

hot
EZ Lok SK21010 Kit inserti filettati elicoidali, acciaio inossidabile 304, dimensioni filettatura 3/8"-16, lunghezza installata 0,375" (confezione da 10)
3.2/5

€ 70.36

EZ Lok SK21010 Kit inserti filettati elicoidali, acciaio inossidabile 304, dimensioni filettatura 3/8"-16, lunghezza installata 0,375" (confezione da 10)
3.2/5

€ 70.36

hot
EZ Lok SK40615 Kit inserti filettati elicoidali metrici, acciaio inossidabile 304, dimensioni filettatura M6-1.0, lunghezza installazione 9 mm (confezione da 10)
3.3/5

€ 66.86

EZ Lok SK40615 Kit inserti filettati elicoidali metrici, acciaio inossidabile 304, dimensioni filettatura M6-1.0, lunghezza installazione 9 mm (confezione da 10)
3.3/5

€ 66.86

hot
EZ Lok SK30620 Kit di inserti filettati elicoidali, acciaio inossidabile 304, dimensione filettatura #10-32, lunghezza installata 0,380" (confezione da 10)
3.3/5

€ 64.81

EZ Lok SK30620 Kit di inserti filettati elicoidali, acciaio inossidabile 304, dimensione filettatura #10-32, lunghezza installata 0,380" (confezione da 10)
3.3/5

€ 64.81

hot
EZ Lok SK20515 Kit di inserti filettati elicoidali, acciaio inossidabile 304, dimensione filettatura #8-32, lunghezza installata 0,246" (confezione da 10)
3.5/5

€ 72.61

EZ Lok SK20515 Kit di inserti filettati elicoidali, acciaio inossidabile 304, dimensione filettatura #8-32, lunghezza installata 0,246" (confezione da 10)
3.5/5

€ 72.61

hot
Inserto filettato EZ LOK per inserti filettati in acciaio inossidabile 303, filettatura interna 8-32, filettatura esterna 5/16-18, lunghezza 0,290"- (confezione da 20.100 pezzi totali) # 8-32 IT, 5/16"-18 ET, 0,290" L 100
4.1/5

€ 330.68

Inserto filettato EZ LOK per inserti filettati in acciaio inossidabile 303, filettatura interna 8-32, filettatura esterna 5/16-18, lunghezza 0,290"- (confezione da 20.100 pezzi totali) # 8-32 IT, 5/16"-18 ET, 0,290" L 100
4.1/5

€ 330.68

hot
EZ Lok EK51220 Kit inserti filettati elicoidali metrici, acciaio inossidabile 304, dimensione filettatura M16-1.5, lunghezza installazione 32 mm (confezione da 5), ​​dimensione filettatura argento M16-1.5, lunghezza installazione 32 mm confezione da 5
3.5/5

€ 89.17

EZ Lok EK51220 Kit inserti filettati elicoidali metrici, acciaio inossidabile 304, dimensione filettatura M16-1.5, lunghezza installazione 32 mm (confezione da 5), ​​dimensione filettatura argento M16-1.5, lunghezza installazione 32 mm confezione da 5
3.5/5

€ 89.17

hot
EZ Lok SK50820 Kit inserti filettati elicoidali metrici, acciaio inossidabile 304, dimensione filettatura M8-1.0, lunghezza installazione 16 mm (confezione da 10)
0.1/5

€ 65.30

EZ Lok SK50820 Kit inserti filettati elicoidali metrici, acciaio inossidabile 304, dimensione filettatura M8-1.0, lunghezza installazione 16 mm (confezione da 10)
0.1/5

€ 65.30

hot
EZ Lok SK40715 Kit inserti filettati elicoidali metrici, acciaio inossidabile 304, dimensione filettatura M7-1.0, lunghezza installata 10,5 mm (confezione da 10)
3.4/5

€ 62.70

EZ Lok SK40715 Kit inserti filettati elicoidali metrici, acciaio inossidabile 304, dimensione filettatura M7-1.0, lunghezza installata 10,5 mm (confezione da 10)
3.4/5

€ 62.70

Scopri il nostro network internazionale

Spediamo in 28 paesi, oltre 200.000 prodotti. Resta aggiornato, iscriviti alla newsletter.

Shopping Cart

Totale:€ 0.00

Vedi carrelloCheckout

Categorie

Tutte le categorie
Menu Categorie Cerca Carrello

Menu