Anderson Metals 56103-08 Raccordo per tubi in ottone, accoppiamento, tubo femmina 1/2" x 1/2" 1/2" x 1/2" 1

Brand:Anderson Metals

3.7/5

€
27.33

Il raccordo per tubo di accoppiamento Anderson Metals è realizzato in ottone e presenta connessioni filettate National Pipe Taper (NPT) femmina. Questo raccordo di accoppiamento collega due tubi che vanno nella stessa direzione con lo stesso diametro per prolungare un tratto rettilineo. Ha filettature NPT femmina per il collegamento a tubi filettati maschio, creando una tenuta più stretta rispetto alle filettature diritte. Questo raccordo è realizzato in ottone per resistenza alla corrosione, duttilità alle alte temperature e bassa permeabilità magnetica. L'ottone può essere collegato a rame, ottone, plastica, alluminio e acciaio saldato. Le temperature di esercizio per questo raccordo vanno da -53 a 121 gradi C (da -65 a 250 gradi F). Questo raccordo soddisfa le specifiche B584 dell'American Society for Testing and Materials (ASTM) e dell'American Society of Mechanical Engineers (ASME)/American National Standards Institute (ANSI) B16 per la garanzia della qualità. I raccordi per tubi sono componenti utilizzati per collegare, terminare, controllare il flusso e cambiare la direzione delle tubazioni in molti settori diversi. Quando acquisti raccordi per tubi, considera l'applicazione, poiché ciò influirà sul tipo di materiale, sulla forma, sulle dimensioni e sulla durata richiesta. I raccordi sono disponibili filettati o non filettati, in molte forme, stili, dimensioni e programmi (spessore della parete del tubo).Anderson Metals produce raccordi, valvole e nippli in ottone. L'azienda, fondata nel 1951, ha sede a Kansas City, MO.

Quantity

Aggiungi al carrello Compra subito

EAN: 0719852936862

Categories: Prodotti industriali e scientifici, Idraulica, pneumatica e idraulica, Raccordi, Raccordi per tubi,

Questi raccordi contengono piombo e la legge federale non ne consente l'installazione per l'uso di acqua potabile negli Stati Uniti e nei suoi territori. Soddisfa le specifiche ASTM B584 e ASME/ANSI B16 per la garanzia della qualità. Le temperature di esercizio vanno da -53 a 121 gradi C (da -65 a 250 gradi F). Ottone per resistenza alla corrosione, duttilità alle alte temperature e bassa permeabilità magnetica. Filettature National Pipe Taper (NPT) femmina per il collegamento a tubi filettati maschio. L'ID del raccordo da ½" sarebbe vicino a ¾". Giunto per il collegamento di due tubi con lo stesso diametro in un tratto rettilineo.

Brand	Anderson Metals
Color	Brass
Connector Type	Coupling
Country of Origin	USA
Domestic Shipping	Item can be shipped within U.S.
Exterior Finish	Brass
International Shipping	This item can be shipped to select countries outside of the U.S.
Is Discontinued By Manufacturer	No
Item Dimensions LxWxH	1 x 1 x 1 inches
Item model number	56103-08
Manufacturer	Anderson Metals
Material	Brass
Number of Pieces	2
Product Dimensions	1 x 1 x 1 inches; 1.13 Ounces
Size	1/2" x 1/2"
Thread Type	NPT

5 Star

4 Star

3 Star

2 Star

1 Star

Scrivi la tua recensione

La tua mail non sarà pubblicata. Tutti i campi obbligatori sono segnati con^*

La tua valutazione

Scritto da: Snide

3/4 x 3/4 female coupler perfect

purchased one. it arrived one day earlier then stated, was in perfect shape, and fit my 3/4" male pipe perfect. so i ordered two more. they also arrived earlier than stated. thank you.

Scritto da: Amazon Customer

quality parts

Excellent price, quality and delivery

Scritto da: Thomas D. Kehoe

Not for 1/4" outside diameter (O.D.) compression fitting

I got perplexed installing a water hammer arrestor. The water hammer arrestor was labeled "1/4" O.D." But its male fittings were 1/4" inside diameter (I.D.). I couldn't understand why this 1/4" I.D. female coupler slid over the male fittings. The male fittings were 0.43" and this female couple is 0.455". After spending way too much time searching on the Internet I put on my mask and went to Home Depot. The plumbing aisle employee told me that the water hammer arrestor had a compression fitting. I went home and found a YouTube video explaining how to connect compression fittings. Twenty minutes later I'd installed my water hammer arrestor, with no extra parts. So I never used this brass coupler but it looks nice. :-) My pipe is 0.25" inside diameter and the outside diameter of the male threads are 0.43". This coupling has an inside diameter of the female threads of 0.44". It slides right over my pipe without engaging. Apparently there are different plumbing "standards" where "1/4-inch" means different sizes. The specs should say what the diameter of the threads are and what pipe it threads onto.

Scritto da: James Barr

Needed For A Propane Quick Connection

I purchased a propane quick connect hose, and then discovered I could not connect to a LPG generator from a 5th Wheel quick connect outlet. This double female coupling allowed me to make the connection. I removed the safety quick connect valve, installed the coupling, and attached a 1/4 inch male quick connection, which I inserted into the generator safety coupling valve. Difficult to find on Amazon, and local hardware stores were clueless on LP quick connections.

Scritto da: Dale Williams

Great products! You will not be disappointed.

I had to make an extension pipe for a propane manifold. This coupler saved the day! The hex nut fittings they make are 2nd to none. I have been using Anderson Metals products for quite awhile now. I have never had one fail! I recommend these to anyone that has a plumbing job.

Scritto da: victor neal

Perfect fit

Item worked perfectly

Scritto da: Rvrguyd

1/4" pipe coupling

The 1/4" is the inside hole diameter. The outside diameter is about 3/8". The threads on one end got a little smashed and threading the pipe on it was a challenge but I got it to fit since brass is soft enough to work with so long as you don't cross thread it.

Scritto da: K. Matsinger

Brass fitting for shower

Need new Brass fitting or my updated walk in shower, local Ace said be hard to find what I needed but Amazon it on Amazon it was perfect. GRACIAS!

Scritto da: Mar co

this is not for shower

i bought this one but this is not for shower (its hard to find female to female pipe ends) inside theres no stopper for the rubber. inside is a straight hole. i still try to put 2 round rubbers inside. and put lots of teflon tape on the male pipe. its ok but theres leak but not too much.

Scritto da: Robert L.

Works for Air Compressor, Air Hose Adapter, Water Separator / filter Connections

I'm using this to connect my air compressor with my air separator or hose adapter and it works very well. Material is good, not flimsy. Also air tight, no leakage for me and I'm not using Teflon tape.

Scritto da: Bruce H

Thin walled.

I used it as a connection between air hoses. The thickness of the wall is a bit thin. One I had before split after a year.

Scritto da: Cloud Morrish

It’s a brass pipe…

It is what it is. A brass pipe coupler. It does the job it was made to do.

Scritto da: Shining star

Shipped wrong item waste of time

Order a 1/4” and got sent 3/8”…!!! Disappointed as it was such a waste of my time waiting for this to arrive!!!!